Best #8 Screws for Drawer Slides (Recycle Factory Screws!)

If you buy something through our links, this site will earn a commission. As an Amazon Associate I earn from qualifying purchases.

#8 screws that come with drawers slides are typically junk. And I’ve both experienced this and read the reviews that have dinged good drawer slides over a simple screw. What’s so special about a good #8 wood screw? Well, it needs aggressive threads, a large truss head and a well made head for driving.

Otherwise, your perfect drawer adjustment will come out of alignment over normal use of the drawer. And nobody wants to install a drawer slide twice.

Consider these factors:

    • Most cabinet sides are made from MDF (medium density fiberboard)
    • Shallow threaded screws will strip easily in MDF and fail over time
    • Aggressive threads, like found in the Rok #8 screws, will grab and hold in MDF and standard plywoods

And I’ve installed a lot of drawers. Bad screws are a top 3 frustration.

What is the diameter of a #8 screw?

First, screws are measured by the “major thread” diameter. Or, in simple terms, the widest part of the screw (not the head).
Taking a look, then, at the major thread diameter of a #8 screw and closest screws you’ll see a #8 screw is .164″ in diameter:
    • #6 screws: .138″ or ~9/64″ diameter
    • #7 screws: .151″ or ~5/32″ diameter
    • #8 screws: .164″ or ~5/32″ diameter
    • #9 screws: .177″ or 11/64″ diameter
    • #10 screws: .190″ or 3/16″ diameter

For a complete rundown of sizings check out this handy guide at Bolt Depot.

So what makes for variations in #8 screws?

Especially if they are all the same diameter, right?

The answer is the size of the shaft, which is the core of the screw where the threads terminate, and the cut of the threads themselves.


    • A large shaft will result in a shallow thread (less gripping area)
    • While on the other hand, a thin shaft will allow for a deep thread
    • And a deep thread will have more surface area exposed against the material it is inserted into

Now most #8 screws for drawers are too short to have advanced features like what GRK put into their cabinet screws, but the thin shaft and deep thread offer a distinct advantage in materials like MDF that are relatively weak.

But do I need to drill a pilot hole?

This isn’t a yes or no question, unfortunately. So here’s a starting point, and then make sure to test out your hardwoods and softwoods with the #8 screws you are using:

    • For #8 screws under 3/4″ most can go into softwood, plywood and MDF without a pilot hole.
    • However for any screws in hardwood a pilot hole is needed.
    • All screws 3/4″ and longer that do not have a self-tapping design should have a pilot hole to prevent splitting of the wood

Failing to drill a pilot hole when needed can either split the wood or break the screw. And both are bad when it comes to needing to extract the screw or use the now damaged wood to hold a screw.

3 Reasons Screws Matter in Drawer Installation

Not everyone likes to plan the details, but if you’re willing to invest a few minutes in planning and buying the right screws it’s worth it.

Especially if your project involves a retrofit where you’ll be working in a cabinet with a counter already installed. Due to limited space and visibility the screw really matters.

Reason #1: Prevent stripping

Well hey, not that kind of stripping.

But instead think about deep threads vs. shallow threads and an analogy like trying to pull a heavy object across the floor and your fingers are the “threads”.

Would you grab the object with just the first joint of your fingers (shallow) or all three joints (deep)? Correct, you’d want all the leverage and holding force you could muster. Or your fingers might slip off.

So the same goes with drawers, which can hold upwards of 100 pounds with just 4-6 screws holding the weight.

Reason #2: Long term holding power

Maybe you enjoy repairing things, but I sure don’t.

15 years ago I built and installed 20+ drawers in my current kitchen. And I haven’t adjusted a single one because I used the right screws.

I did, however, use the factory screws in a cherry dresser with side mount ball bearing screws. And guess what? Yep, they have stripped and loosened as the 50 pound drawers have worked against the screw year over year.

Reason #3: Added safety

In my kitchen I have a rather large drawer in the bottom stack of cabinets. And it is stuffed full of kids coloring books, markers and I don’t know what else.

And watching my kids as they aged through 18 months up to 5 years lean on this drawer always made me nervous. While it was secured in with the right screws and well adjusted drawer slides (and never failed) safety is certainly something to consider.

Due to many drawers featuring up to 100 pound load capacity with full extensions just think of the force on that rear mounting bracket and the 2 screws typically used to hold it in.

Frequently Asked Questions for #8 Screws


Who thought there could be so much to a #8 screw? For more reading check out our articles on the best drawer slides.

Recommended Reading

Leave a Comment

Exit mobile version